An Oiling System Manufacturer Integrating Design, Production And Sales, With Its Own Brand TRIBOS, Has Been Committed To The Development And Production Of Precision Automatic Oiling Devices For Stamping Processing For Many Years
Can oiling: the working principle of can oiling and process design
We all know that can oiling is very important for the product, not only to ensure that the subsequent processing does not occur in the broken phenomenon, and the user will be more comfortable in the use of the time to protect the life of the goods, and also to obtain the user's unanimous praise, which often have an inseparable relationship with the working principle of can oiling and the entire process design.
The spraying mechanism installed on both sides of the can oiling machine will gradually suck out the oil from the storage tank by way of compressed air and spray out very small mist particles through the nozzle, and the oil will be automatically screened and filtered out when it passes through a number of special structures such as atomizing guns, leaving only micron-sized fine particles, which will enter the ionization zone in both sides of the aluminum foil oiling machine tank under the guidance of the secondary airflow. The large oil droplets will be fully blocked and will then flow back into the tank quickly along the inner wall of the mailbox through the recycling link. A certain amount of air pressure will be produced in the nozzle to produce a quantitative oil spray from which the oil mist produced at this time will often be much more than the amount needed.
Then the can oiling machine will be driven by the secondary airflow to make the fog into the ionization zone, in the process of movement will be further screening of the oil mist, only the particles that meet the relevant requirements will enter the last zone, and finally produce a strong voltage to the ionization zone, making each oil particles at this moment full of charge. After ionization, the particles will rise to the chamber with the thin oiling machine, thus entering between the moving aluminum foil and the high voltage drive plate, and then through the high voltage drive plate, with the location of the electric charge, driving the oil mist to reach the grounded metal belt above all drained, to be in this can completely absorb the charged particles.
The process flow of the can oiling machine is designed in most factories along the lines of the can foil slag off line, followed by the cleaning line, and then after the large roll annealing and large roll oiling, the finished product can be slit. In order to ensure that the physical properties of the cans can be oiled to meet the needs of each customer under this process, the manufacturer will carry out a temperature measurement of the cans with steel sleeves, which shows that the temperature can be 280 degrees Celsius after 14 hours to meet the needs of customers.
The above is the working principle of can oiling and the design of the entire process, if you have any questions about can oiling, you can read more about it.
Aluminum foil oiling can be divided into sheet aluminum foil according to its shape. Most of the raw materials for the deep processing of aluminum foil are supplied in roll form. Only a few manual packaging occasions use aluminum foil. Aluminum foil coating oil can be divided into hard foil and soft foil according to its status. Aluminum foil oiled hard foil: Rolled aluminum foil without softening treatment (annealing) and degreasing treatment has a residual surface.
Aluminum foil coated with oil is a stamping material made of aluminum rolled directly onto a thin sheet. The stamping effect of aluminum foil coated with oil is similar to that of pure silver foil, so it is also called fake silver foil. Due to its softness and ductility, aluminum has a silvery-white luster. Aluminum foil can also be printed if the rolled sheet is mounted on offset paper with sodium silicate and other materials.
Knife beam type electrostatic oiling equipment is oil pump directly on the knife beam, through the tiny gap of the knife beam to spray oil. Because the gap of the knife beam is very small, so the oil purity requirements are very high. In actual production, it is impossible to completely clean the annealed strip or the cleaned strip surface with more or less residual iron powder and dust, which will inevitably cause the knife beam (especially the lower knife beam) to be blocked during the continuous production process, resulting in uneven oiling or leakage on the strip surface. Nozzle type electrostatic oiling equipment uses air pressure to pump oil to the nozzle and then sprays the oil out, so even if there are some tiny impurities in the oil under the pressure of the pump and air, the nozzle will not be clogged. Even if there is slight clogging, the impurities can be blown out of the nozzle by directly increasing the air flow, thus ensuring the quality of oiling.
Today, with the flourishing of science and technology, the help of oiling equipment is indispensable for everything from hot water to security doors, to cars or buildings. It can be said that because of the existence of oiling equipment, it not only saves the time we don't need to waste in our daily life, but also reduces some unnecessary expenses and plays a significant role in the direction of our business. On the contrary, some delays in production or mistakes in details may bring adverse effects to ourselves, so it is still important to grasp this link.
The electrostatic oiling equipment consists of oiling chamber, high voltage electrostatic power supply, oil supply system, oil circuit heating and circulating system, electric control system and operating table. The upper and lower oiling knife beams/nozzles are horizontally installed in the oiling chamber, and the steel plate can pass through freely. The oil supply system quantifies the oil supplied to the oiling knife beam/nozzle to flow evenly from the knife gap of the knife beam and nozzle.
Electrostatic oiling equipment is a device that uses high voltage electrostatic to evenly spray antirust oil or other process media on the surface of the plate and strip. Composition: Electrostatic oiling equipment consists of oiling chamber, high voltage electrostatic power supply, oil supply system, electric control system and operating table.